i2c-sensors-ex4
をテンプレートにして作成
[
トップ
] [
新規
|
一覧
|
単語検索
|
最終更新
|
ヘルプ
]
開始行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex4 or http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex4
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program sensors
program: 'ex("service","clear sendBuffer")
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init hdc1080
program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
program: '
program: 'get temp
program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
program: delay(15)
program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
program: 'temp=s2i(v1s)/65536.0*165-40
program: v1=s2i(v1s)
program: if v1<0 then v1x=2.0*(v1/2+0x8000) else v1x=1.0*v1
program: temp=v1x/65536.0*165-40
program: '
program: 'delay(20)
program: '
program: 'get humidity
program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
program: delay(15)
program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
program: v2=s2i(v2s)
program: if v2<0 then v3=2.0*(v2/2 + 0x8000) else v3=v2*1.0
program: humid=(v3/65536.0) *100
program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
program: delay(40)
program: '
program: ' init lux sensor
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: 'get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: v=s2i(v2)*256+s2i(v1)
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: ex("pi4j", "i2c close.")
program: ex("service","sendResults.")
command: end sensors
command: run sensors
result:
device=temp, Date=2019/6/8/ 20:52:56, v=27.5347900390625
device=humid, Date=2019/6/8/ 20:52:56,v=61.07177734375
device=lux, Date=2019/6/8/ 20:52:56, v=16
device=temp, Date=2019/6/8/ 20:53:25, v=27.554931640625
device=humid, Date=2019/6/8/ 20:53:25,v=64.141845703125
device=lux, Date=2019/6/8/ 20:53:25, v=16
device=temp, Date=2019/6/8/ 20:53:55, v=27.554931640625
device=humid, Date=2019/6/8/ 20:53:55,v=61.175537109375
device=lux, Date=2019/6/8/ 20:53:55, v=16
device=temp, Date=2019/6/8/ 20:54:25, v=27.70599365234375
device=humid, Date=2019/6/8/ 20:54:25,v=67.083740234375
device=lux, Date=2019/6/8/ 20:54:25, v=16
device=temp, Date=2019/6/8/ 20:54:55, v=27.8167724609375
device=humid, Date=2019/6/8/ 20:54:55,v=64.312744140625
device=lux, Date=2019/6/8/ 20:54:56, v=16
currentDevice="yamaRasPiDp1_1",Date=2019/6/8/ 20:54:56
終了行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex4 or http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex4
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program sensors
program: 'ex("service","clear sendBuffer")
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init hdc1080
program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
program: '
program: 'get temp
program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
program: delay(15)
program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
program: 'temp=s2i(v1s)/65536.0*165-40
program: v1=s2i(v1s)
program: if v1<0 then v1x=2.0*(v1/2+0x8000) else v1x=1.0*v1
program: temp=v1x/65536.0*165-40
program: '
program: 'delay(20)
program: '
program: 'get humidity
program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
program: delay(15)
program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
program: v2=s2i(v2s)
program: if v2<0 then v3=2.0*(v2/2 + 0x8000) else v3=v2*1.0
program: humid=(v3/65536.0) *100
program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
program: delay(40)
program: '
program: ' init lux sensor
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: 'get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: v=s2i(v2)*256+s2i(v1)
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: ex("pi4j", "i2c close.")
program: ex("service","sendResults.")
command: end sensors
command: run sensors
result:
device=temp, Date=2019/6/8/ 20:52:56, v=27.5347900390625
device=humid, Date=2019/6/8/ 20:52:56,v=61.07177734375
device=lux, Date=2019/6/8/ 20:52:56, v=16
device=temp, Date=2019/6/8/ 20:53:25, v=27.554931640625
device=humid, Date=2019/6/8/ 20:53:25,v=64.141845703125
device=lux, Date=2019/6/8/ 20:53:25, v=16
device=temp, Date=2019/6/8/ 20:53:55, v=27.554931640625
device=humid, Date=2019/6/8/ 20:53:55,v=61.175537109375
device=lux, Date=2019/6/8/ 20:53:55, v=16
device=temp, Date=2019/6/8/ 20:54:25, v=27.70599365234375
device=humid, Date=2019/6/8/ 20:54:25,v=67.083740234375
device=lux, Date=2019/6/8/ 20:54:25, v=16
device=temp, Date=2019/6/8/ 20:54:55, v=27.8167724609375
device=humid, Date=2019/6/8/ 20:54:55,v=64.312744140625
device=lux, Date=2019/6/8/ 20:54:56, v=16
currentDevice="yamaRasPiDp1_1",Date=2019/6/8/ 20:54:56
ページ名:
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
