i2c-sensors-ex3-w1
をテンプレートにして作成
[
トップ
] [
新規
|
一覧
|
単語検索
|
最終更新
|
ヘルプ
]
開始行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1 or http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program sensors
program: 'ex("service","clear sendBuffer")
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init hdc1080
program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
program: '
program: 'get temp
program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
program: delay(15)
program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
program: temp=s2i(v1s)/65536.0*165-40
program: '
program: 'get humidity
program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
program: delay(15)
program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
program: humid=s2i(v2s)/65536.0*100
program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
program: '
program: ' init lux sensor
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: 'get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: v=s2i(v2)*256+s2i(v1)
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: ' init barometer , MPL3115A2
program: 'ex("pi4j", "i2c write1 0x60,0x26,0xbb") 'set to altmeter with an OSR=128
program: 'ex("pi4j", "i2c write1 0x60,0x13,0x07") 'enable data flags in PT_DATA_CFG
program: 'ex("pi4j", "i2c write1 0x60,0x28,0x11") 'set int to acive low open drain
program: 'ex("pi4j", "i2c write1 0x60,0x29,0x80") 'enabledrdy interrupt
program: 'ex("pi4j", "i2c write1 0x60,0x26,0x39") 'Active mode, OSR=128, barometer mode(0x39)
program: 'delay(10)
program: '
program: '#define CTRL_REG1 0x26
program: '
program: ' init
program: ' - set Mode Stanby
program: ' -- clear Register Bit CTRL_REG1 0x01
program: ' --- temp = i2cRead(CTRL_REG1)
program: temps=ex("pi4j", "i2c read1 0x60,0x26")
program: ' --- temp &= ~(0x01)
program: temp=s2i(temps)
program: temp=temp & 0xfe
program: ' --- i2cwrite(CTRL_REG1, 0x01)
program: ex("pi4j", "i2c write1 0x60,0x26,"+temp)
program: '
program: delay(1)
program: '
program: ' - set Mode Altimeter
program: ' -- set Register Bit CTR_REG1 0x80
program: ' --- temp = i2cread(CTR_REG1)
program: temps=ex("pi4j","i2c read1 0x60,0x26")
program: ' --- temp |= 0x80
program: temp=s2i(temps)
program: temp=temp | 0x80
program: ' --- i2cwrite(CTR_REG1, temp)
program: ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
program: '
program: delay(1)
program: '
program: ' - set Over Sample Rate r(=7)
program: ' -- if r >7 then r=7;
program: ' -- r<<=3
program: r=7*8 '8=2^3
program: ' -- temp = i2cRead(CTRL_REG1)
program: temps=ex("pi4j", "i2c read1 0x60,0x26")
program: ' -- temp &= 0xc7
program: temp=s2i(temps)
program: temp=temp & 0xc7
program: ' -- temp |= r
program: temp= temp | r
program: ' -- i2cwrite(CTRL_REG1, temp)
program: ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
program: '
program: delay(1)
program: '
program: ex("pi4j", "i2c close.")
program: ex("service","sendResults.")
command: end sensors
command: run sensors
result:
device=temp, Date=2019/2/23/ 17:39:4, v=19.40765380859375
device=humid, Date=2019/2/23/ 17:39:4,v=48.291015625
device=lux, Date=2019/2/23/ 17:39:4, v=13
device=temp, Date=2019/2/23/ 17:39:33, v=19.48822021484375
device=humid, Date=2019/2/23/ 17:39:33,v=48.291015625
device=lux, Date=2019/2/23/ 17:39:33, v=13
currentDevice="yamaRasPiDp1_1",Date=2019/2/23/ 17:39:33
終了行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1 or http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program sensors
program: 'ex("service","clear sendBuffer")
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init hdc1080
program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
program: '
program: 'get temp
program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
program: delay(15)
program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
program: temp=s2i(v1s)/65536.0*165-40
program: '
program: 'get humidity
program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
program: delay(15)
program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
program: humid=s2i(v2s)/65536.0*100
program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
program: '
program: ' init lux sensor
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: 'get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: v=s2i(v2)*256+s2i(v1)
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: ' init barometer , MPL3115A2
program: 'ex("pi4j", "i2c write1 0x60,0x26,0xbb") 'set to altmeter with an OSR=128
program: 'ex("pi4j", "i2c write1 0x60,0x13,0x07") 'enable data flags in PT_DATA_CFG
program: 'ex("pi4j", "i2c write1 0x60,0x28,0x11") 'set int to acive low open drain
program: 'ex("pi4j", "i2c write1 0x60,0x29,0x80") 'enabledrdy interrupt
program: 'ex("pi4j", "i2c write1 0x60,0x26,0x39") 'Active mode, OSR=128, barometer mode(0x39)
program: 'delay(10)
program: '
program: '#define CTRL_REG1 0x26
program: '
program: ' init
program: ' - set Mode Stanby
program: ' -- clear Register Bit CTRL_REG1 0x01
program: ' --- temp = i2cRead(CTRL_REG1)
program: temps=ex("pi4j", "i2c read1 0x60,0x26")
program: ' --- temp &= ~(0x01)
program: temp=s2i(temps)
program: temp=temp & 0xfe
program: ' --- i2cwrite(CTRL_REG1, 0x01)
program: ex("pi4j", "i2c write1 0x60,0x26,"+temp)
program: '
program: delay(1)
program: '
program: ' - set Mode Altimeter
program: ' -- set Register Bit CTR_REG1 0x80
program: ' --- temp = i2cread(CTR_REG1)
program: temps=ex("pi4j","i2c read1 0x60,0x26")
program: ' --- temp |= 0x80
program: temp=s2i(temps)
program: temp=temp | 0x80
program: ' --- i2cwrite(CTR_REG1, temp)
program: ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
program: '
program: delay(1)
program: '
program: ' - set Over Sample Rate r(=7)
program: ' -- if r >7 then r=7;
program: ' -- r<<=3
program: r=7*8 '8=2^3
program: ' -- temp = i2cRead(CTRL_REG1)
program: temps=ex("pi4j", "i2c read1 0x60,0x26")
program: ' -- temp &= 0xc7
program: temp=s2i(temps)
program: temp=temp & 0xc7
program: ' -- temp |= r
program: temp= temp | r
program: ' -- i2cwrite(CTRL_REG1, temp)
program: ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
program: '
program: delay(1)
program: '
program: ex("pi4j", "i2c close.")
program: ex("service","sendResults.")
command: end sensors
command: run sensors
result:
device=temp, Date=2019/2/23/ 17:39:4, v=19.40765380859375
device=humid, Date=2019/2/23/ 17:39:4,v=48.291015625
device=lux, Date=2019/2/23/ 17:39:4, v=13
device=temp, Date=2019/2/23/ 17:39:33, v=19.48822021484375
device=humid, Date=2019/2/23/ 17:39:33,v=48.291015625
device=lux, Date=2019/2/23/ 17:39:33, v=13
currentDevice="yamaRasPiDp1_1",Date=2019/2/23/ 17:39:33
ページ名:
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
