i2c-opt3001-1
をテンプレートにして作成
[
トップ
] [
新規
|
一覧
|
単語検索
|
最終更新
|
ヘルプ
]
開始行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-opt3001-1 or http://www.yama-lab.org/fwb4pi/index.php?i2c-opt3001-1
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program i2cOpt3001
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init opt3001
program: ex("pi4j", "i2c write2 0x44,0x01,0xcc,0x01") ' config
program: delay(10)
program: '
program: 'get lux
program: ex("pi4j", "i2c write-b 0x44,0x00") ' raw-lax
program: delay(300)
program: v1s=ex("pi4j", "i2c read-A-2 0x44") ' get raw-lax
program: 'v1s=ex("pi4j", "i2c read2 0x44,0x00")
program: luxw1=(s2i(v1s) /(2^12)) & 0x000f
program: luxw2=s2i(v1s) & 0x0fff
program: lux=luxw2*(2^luxw1)
program: '
program: ex("pi4j", "i2c close.")
program: 'ex("service","clear sendBuffer")
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+lux)
program: ex("service","sendResults.")
command: end i2cOpt3001
command: run i2cOpt3001
result:
device=lux, Date=2019/2/20/ 20:20:29, v=0
device=lux, Date=2019/2/20/ 20:20:58, v=0
currentDevice="yamaRasPiDp1_1",Date=2019/2/20/ 20:20:58
終了行:
[[FrontPage]]
objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-opt3001-1 or http://www.yama-lab.org/fwb4pi/index.php?i2c-opt3001-1
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program i2cOpt3001
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init opt3001
program: ex("pi4j", "i2c write2 0x44,0x01,0xcc,0x01") ' config
program: delay(10)
program: '
program: 'get lux
program: ex("pi4j", "i2c write-b 0x44,0x00") ' raw-lax
program: delay(300)
program: v1s=ex("pi4j", "i2c read-A-2 0x44") ' get raw-lax
program: 'v1s=ex("pi4j", "i2c read2 0x44,0x00")
program: luxw1=(s2i(v1s) /(2^12)) & 0x000f
program: luxw2=s2i(v1s) & 0x0fff
program: lux=luxw2*(2^luxw1)
program: '
program: ex("pi4j", "i2c close.")
program: 'ex("service","clear sendBuffer")
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+lux)
program: ex("service","sendResults.")
command: end i2cOpt3001
command: run i2cOpt3001
result:
device=lux, Date=2019/2/20/ 20:20:29, v=0
device=lux, Date=2019/2/20/ 20:20:58, v=0
currentDevice="yamaRasPiDp1_1",Date=2019/2/20/ 20:20:58
ページ名:
![[PukiWiki]](image/pukiwiki.png "[PukiWiki]")
