i2c-sensors-ex3-w1 の変更点

追加された行はこの色です。
削除された行はこの色です。
i2c-sensors-ex3-w1 へ行く。
i2c-sensors-ex3-w1 の差分を削除
[[FrontPage]]
 objectPage http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1 or http://www.yama-lab.org/fwb4pi/index.php?i2c-sensors-ex3-w1
 device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
 command: set readInterval=30000
 command: set execInterval=0
 command: set reportLength=120
 command: program sensors
 program: 'ex("service","clear sendBuffer")
 program: '
 program: ' init i2c
 program: ex("pi4j", "i2c use 1")
 program: '
 program: ' init hdc1080 
 program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
 program: '
 program: 'get temp
 program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
 program: delay(15)
 program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
 program: temp=s2i(v1s)/65536.0*165-40
 program: '
 program: 'get humidity
 program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
 program: delay(15)
 program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
 program: humid=s2i(v2s)/65536.0*100
 program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
 program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
 program: '
 program: ' init lux sensor 
 program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
 program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
 program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
 program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
 program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
 program: delay(50)
 program: '
 program: 'get the lux value
 program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
 program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
 program: v=s2i(v2)*256+s2i(v1)
 program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
 program: '
 program: ' init barometer , MPL3115A2
 program: 'ex("pi4j", "i2c write1 0x60,0x26,0xbb") 'set to altmeter with an OSR=128
 program: 'ex("pi4j", "i2c write1 0x60,0x13,0x07") 'enable data flags in PT_DATA_CFG
 program: 'ex("pi4j", "i2c write1 0x60,0x28,0x11") 'set int to acive low open drain
 program: 'ex("pi4j", "i2c write1 0x60,0x29,0x80") 'enabledrdy interrupt
 program: 'ex("pi4j", "i2c write1 0x60,0x26,0x39") 'Active mode, OSR=128, barometer mode(0x39)
 program: 'delay(10)
 program: '
 program: '#define CTRL_REG1           0x26 
 program: '
 program: ' init
 program: ' - set Mode Stanby
 program: ' -- clear Register Bit CTRL_REG1 0x01
 program: ' --- temp = i2cRead(CTRL_REG1)
 program:    temps=ex("pi4j", "i2c read1 0x60,0x26")
 program: ' --- temp &= ~(0x01)
 program:    temp=s2i(temps)
 program:    temp=temp & 0xfe
 program: ' --- i2cwrite(CTRL_REG1, 0x01)
 program:    ex("pi4j", "i2c write1 0x60,0x26,"+temp)
 program: '
 program:  delay(1)
 program: '
 program: ' - set Mode Altimeter
 program: ' -- set Register Bit CTR_REG1 0x80
 program: ' --- temp = i2cread(CTR_REG1)
 program:    temps=ex("pi4j","i2c read1 0x60,0x26")
 program: ' --- temp |= 0x80
 program:    temp=s2i(temps)
 program:    temp=temp | 0x80
 program: ' --- i2cwrite(CTR_REG1, temp)
 program:    ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
 program: '
 program:   delay(1)
 program: '
 program: ' - set Over Sample Rate r(=7)
 program: ' --  if r >7 then r=7;
 program: ' -- r<<=3
 program:    r=7*8   '8=2^3
 program: ' -- temp = i2cRead(CTRL_REG1)
 program:    temps=ex("pi4j", "i2c read1 0x60,0x26")
 program: ' -- temp &= 0xc7
 program:     temp=s2i(temps)
 program:     temp=temp & 0xc7
 program: ' -- temp |= r
 program:      temp= temp | r
 program: ' -- i2cwrite(CTRL_REG1, temp)
 program:      ex("pi4j", "i2c write1 0x60, 0x26, "+temp)
 program: '
 program:  delay(1)
 program:  '
 program: ex("pi4j", "i2c close.")
 program: ex("service","sendResults.")
 command: end sensors
 command: run sensors
 result:
 device=temp, Date=2019/2/23/ 17:39:4, v=19.40765380859375
 device=humid, Date=2019/2/23/ 17:39:4,v=48.291015625
 device=lux, Date=2019/2/23/ 17:39:4, v=13
 currentDevice="yamaRasPiDp1_1",Date=2019/2/23/ 17:39:4

 device=temp, Date=2019/2/23/ 17:39:33, v=19.48822021484375
 device=humid, Date=2019/2/23/ 17:39:33,v=48.291015625
 device=lux, Date=2019/2/23/ 17:39:33, v=13
 currentDevice="yamaRasPiDp1_1",Date=2019/2/23/ 17:39:33