sensors-class-1 のバックアップ(No.1)

バックアップ一覧
差分を表示
現在との差分を表示
ソースを表示
sensors-class-1 へ行く。
- 1 (2018-09-16 (日) 10:26:44)
- 2 (2018-09-16 (日) 11:46:34)
objectPage http://www.yama-lab.org/fwb4pi/index.php?Sensors3 or http://www.yama-lab.org/fwb4pi/index.php?Sensors3
device yamaRasPiDp9_1 or yamaRasPiDp9_2 start after no write for 10 min.
command: set readInterval=30000
command: set execInterval=0
command: program Sensors
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program:  init lux sensor 
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: lux=s2i(v2)*256+s2i(v1)
program: '
program: 'get the Aanalog value from the ADS1115 ch0
#  // Start with default values
#  uint16_t config = ADS1015_REG_CONFIG_CQUE_NONE    | // Disable the comparator (default val)
#                    ADS1015_REG_CONFIG_CLAT_NONLAT  | // Non-latching (default val)
#                    ADS1015_REG_CONFIG_CPOL_ACTVLOW | // Alert/Rdy active low   (default val)
#                    ADS1015_REG_CONFIG_CMODE_TRAD   | // Traditional comparator (default val)
#                    ADS1015_REG_CONFIG_DR_1600SPS   | // 1600 samples per second (default)
#                    ADS1015_REG_CONFIG_MODE_SINGLE;   // Single-shot mode (default)
#
program: config=0x0003|0x0000|0x0000|0x0000|0x0080|0x0100
#
#  // Set PGA/voltage range
#  config |= m_gain;
program: config=config|0x0000
#
#  // Set single-ended input channel
#  switch (channel)
#  {
#    case (0):
#      config |= ADS1015_REG_CONFIG_MUX_SINGLE_0; //SINGLE_1, SINGLE_2, SINGLE_3
#      break;
program: config=config|0x4000
#program: config= config|0x5000
#
#  // Set 'start single-conversion' bit
#  config |= ADS1015_REG_CONFIG_OS_SINGLE;
program: config=config|0x8000
#
#  writeRegister(m_i2cAddress, ADS1015_REG_POINTER_CONFIG, config);
#
program: ex("pi4j", "i2c write2 0x49,0x01,"+config)
#
#  // Wait for the conversion to complete
#  delay(m_conversionDelay);
#
program: delay(10)
#
#  // Read the conversion results
#  // Shift 12-bit results right 4 bits for the ADS1015
#  return readRegister(m_i2cAddress, ADS1015_REG_POINTER_CONVERT) >> m_bitShift;  
#
program: v2=ex("pi4j","i2c read2 0x49,0x00")
program: airpol=s2i(v2)
#program: airpol=(airpol+32768)>>4
#
program: '
program: ' get temperature
program: v1=ex("pi4j", "i2c read1 0x48,0x00")
program: tmp=s2i(v1)
program: '
program: ' get motion
program: v1=ex("pi4j","get-a-0")
program: motion=s2i(v1)
program: '
program: ex("pi4j", "i2c close")
program: '
program: date=ex("service","getCurrentDate.")
program: ex("service","clear sendBuffer")
program: ex("service","putSendBuffer device=light, Date="+date+", v="+lux)
program: ex("service","putSendBuffer device=airPol, Date="+date+", v="+airpol)
program: ex("service","putSendBuffer device=temp, Date="+date+", v="+tmp)
program: ex("service","putSendBuffer device=motion, Date="+date+", v="+motion)
program: ex("service","sendResults.")
command: end Sensors
command: run Sensors
result:
device=light, Date=2018/9/16/ 10:26:30, v=5
device=airPol, Date=2018/9/16/ 10:26:30, v=9662
device=temp, Date=2018/9/16/ 10:26:30, v=28
device=motion, Date=2018/9/16/ 10:26:30, v=23
currentDevice="yamaRasPiDp9_1",Date=2018/9/16/ 10:26:30