Diff of sensors-1-h-class

The added line is THIS COLOR.
The deleted line is THIS COLOR.
Go to sensors-1-h-class.
Deleting diff of sensors-1-h-class
[[FrontPage]]
 command: set readInterval=30000
 command: set execInterval=0
 command: set reportLength=600
 command: program sensors
 program: 'ex("service","clear sendBuffer")
 program: '
 program: ' init i2c
 program: ex("pi4j", "i2c use 1")
 program: '
 program: ' init hdc1080 
 program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
 program: '
 program: 'get temp
 program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
 program: delay(15)
 program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
 program: 'temp=s2i(v1s)/65536.0*165-40
 program: v1=s2i(v1s)
 program: if v1<0 then v1x=2.0*(v1/2+0x8000) else v1x=1.0*v1
 program: temp=v1x/65536.0*165-40
 program: '
 program: 'delay(20)
 program: '
 program: 'get humidity
 program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
 program: delay(15)
 program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
 program: v2=s2i(v2s)
 program: if v2<0 then v3=2.0*(v2/2 + 0x8000) else v3=v2*1.0
 program: humid=(v3/65536.0) *100
 program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
 program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
 program: delay(40)
 program: '
 program: ' init lux sensor 
 program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
 program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
 program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
 program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
 program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
 program: delay(50)
 program: '
 program: 'get the lux value
 program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
 program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
 program: v=s2i(v2)*256+s2i(v1)
 program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
 program: '
 program: 'Ardino-I2C PIR sensor 
 program: '
 program: 'get 30sec. motions
 program: v1=ex("pi4j", "i2c read1 0x12,0x01")
 program: v2=ex("pi4j", "i2c read1 0x12,0x02")
 program: v=s2i(v1)*256+s2i(v2)
 program: if v < 120 then
 program: {
 program:   ex("service","putSendBuffer device=pir, Date="+ex("service","getCurrentDate.")+", v="+v)
 program: }
 program: '
 program: '
 program: 'Ardino-I2C CO2 sensor 
 program: '
 program: v1=ex("pi4j", "i2c read1 0x13,0x01")
 program: v2=ex("pi4j", "i2c read1 0x13,0x02")
 program: v=s2i(v1)*256+s2i(v2)
 program: if v<10000 then
 program: {
 program:   ex("service","putSendBuffer device=co2, Date="+ex("service","getCurrentDate.")+", v="+v)
 program: }
program: '
 program: '
 program: 'Ardino-particle(dust) sensor 
 program: '
 program: v1=ex("pi4j", "i2c read1 0x15,0x01")
 program: v2=ex("pi4j", "i2c read1 0x15,0x02")
 program: v=s2i(v1)*256+s2i(v2)
 program: if v<100000 then
 program: {
 program:   ex("service","putSendBuffer device=dst, Date="+ex("service","getCurrentDate.")+", v="+v)
 program: }
 program: '
 program: ex("pi4j", "i2c close.")
 program: ex("service","sendResults.")
 command: end sensors
 command: run sensors
 command: set pageName="sensors-1-h-<hour>"