Backup of sensors-1-h-class(No. 1)

List of Backups
View the diff.
View the diff current.
View the source.
Go to sensors-1-h-class.
- 1 (2019-06-11 (Tue) 17:15:03)
- 2 (2019-06-11 (Tue) 19:31:01)
- 3 (2019-06-11 (Tue) 23:48:15)
- 4 (2019-06-12 (Wed) 09:15:56)
- 5 (2019-06-19 (Wed) 02:12:47)

command: set readInterval=30000
command: set execInterval=0
command: set reportLength=120
command: program sensors
program: 'ex("service","clear sendBuffer")
program: '
program: ' init i2c
program: ex("pi4j", "i2c use 1")
program: '
program: ' init hdc1080 
program: ex("pi4j", "i2c write2 0x40,0x02,0x10,0x00") ' config
program: '
program: 'get temp
program: ex("pi4j", "i2c write-b 0x40,0x00") ' temp
program: delay(15)
program: v1s=ex("pi4j", "i2c read-A-2 0x40") ' get temp
program: 'temp=s2i(v1s)/65536.0*165-40
program: v1=s2i(v1s)
program: if v1<0 then v1x=2.0*(v1/2+0x8000) else v1x=1.0*v1
program: temp=v1x/65536.0*165-40
program: '
program: 'delay(20)
program: '
program: 'get humidity
program: ex("pi4j", "i2c write-b 0x40,0x01") ' get humidity
program: delay(15)
program: v2s=ex("pi4j", "i2c read-A-2 0x40") 'humid
program: v2=s2i(v2s)
program: if v2<0 then v3=2.0*(v2/2 + 0x8000) else v3=v2*1.0
program: humid=(v3/65536.0) *100
program: ex("service","putSendBuffer device=temp, Date="+ex("service","getCurrentDate.")+", v="+temp)
program: ex("service","putSendBuffer device=humid, Date="+ex("service","getCurrentDate.")+",v="+humid)
program: delay(40)
program: '
program: ' init lux sensor 
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") 'power up the tsl2561 lux sensor
program: ex("pi4j", "i2c write1 0x29,0x81,0x00")
program: ex("pi4j", "i2c write1 0x29,0x86,0x00") 'scale
program: ex("pi4j", "i2c write1 0x29,0x80,0x00") 'power down
program: ex("pi4j", "i2c write1 0x29,0x80,0x03") ' power up again
program: delay(50)
program: '
program: 'get the lux value
program: v1=ex("pi4j", "i2c read1 0x29,0x8c")
program: v2=ex("pi4j", "i2c read1 0x29,0x8d")
program: v=s2i(v2)*256+s2i(v1)
program: ex("service","putSendBuffer device=lux, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: 'Ardino-I2C PIR sensor 
program: '
program: 'get 30sec. motions
program: v1=ex("pi4j", "i2c read1 0x12,0x01")
program: v2=ex("pi4j", "i2c read1 0x12,0x02")
program: v=s2i(v1)*256+s2i(v2)
program: ex("service","putSendBuffer device=pir, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: '
program: 'Ardino-I2C CO2 sensor 
program: '
program: v1=ex("pi4j", "i2c read1 0x13,0x01")
program: v2=ex("pi4j", "i2c read1 0x13,0x02")
program: v=s2i(v1)*256+s2i(v2)
program: ex("service","putSendBuffer device=co2, Date="+ex("service","getCurrentDate.")+", v="+v)
program: '
program: ex("pi4j", "i2c close.")
program: ex("service","sendResults.")
command: end sensors
command: run sensors

Backup of sensors-1-h-class (No. 1)